Flame-retardant PC/ABS often loses impact strength after humidity and heat exposure because the aryl phosphate flame retardant hydrolyzes and releases acid that accelerates PC chain scission. Fresh parts pass UL94, but aged parts crack at screw posts and clips. The fix is a hydrolysis resistant formulation, not just a V-0 rating.
The field problem: good parts that fail after aging
A freshly molded flame-retardant PC/ABS part usually looks perfect. The notched impact is high, the UL94 rating is met, and the melt flows cleanly. Then the part sits in a humid warehouse, rides through a hot climate, or lives outdoors for a season. Months later a screw post cracks for no obvious reason, a clip snaps on the third open, or a housing fails in the field.
Most people blame the polycarbonate. Everyone knows PC fears water at high temperature. That view is partly right but incomplete, and it hides the real driver behind a large share of field returns.
How the accelerated aging test was set up
| Parameter | Setting |
| Temperature | 107 degrees Celsius |
| Environment | Humidity and heat, accelerated |
| Duration | 90 hours |
| Measurement | Gel permeation chromatography (GPC) molecular weight |
Gel permeation chromatography tracks molecular weight, the best single proxy for whether the material can still absorb impact. A falling number means the chains are breaking.
What the molecular weight data reveals
Two aryl phosphate flame retardants, the BDP flame retardant and the RDP flame retardant, were compared in PC/ABS under the same aging conditions. The PC molecular weight was measured before and after.
| Flame retardant | Initial molecular weight (g/mol) | After 90 hours (g/mol) | Retention |
| RDP | 55000 | 24000 | 44 percent |
| BDP | 54000 | 42000 | 78 percent |
RDP tells the starkest story. After 90 hours the PC molecular weight fell from 55000 to 24000 g/mol, leaving only about 44 percent of the original chain length. The BDP flame retardant, the more common choice today, still dropped from 54000 to 42000 g/mol. That is a clear chain scission event, not a rounding error.
Flame-retardant PC/ABS humidity heat resistance depends not only on the PC itself but also on whether the phosphate ester flame retardant resists hydrolysis.
The counterintuitive culprit: the flame retardant itself
For years the default story was that PC hydrolyzes and the part weakens. The data above flips part of that story. The aryl phosphate flame retardant, the very additive that earns the V-0 rating, can itself accelerate the damage.
This is the part most teams miss. They optimize the PC grade, dry the resin, and tighten the mold, then watch molecular weight fall anyway. The acid is coming from the flame retardant, not just from ambient moisture attacking the polymer.
How phosphate ester flame retardants attack flame-retardant PC/ABS
The mechanism is a short chain reaction, and each step feeds the next.
Step one is retardant hydrolysis. BDP and RDP are aryl phosphates built from many phosphate ester bonds. Under the combined pressure of high temperature, water, and time, those bonds gradually hydrolyze and form acidic phosphate species carrying a P-OH group. That is the spark.
Step two is acid catalyzed PC hydrolysis. The backbone of PC is the carbonate bond, written as -O-CO-O-. PC does not fall apart on first contact with water. But when water, high temperature, and acid are present together, the carbonate bond hydrolyzes much faster and the molecular weight slides downward without stopping.
So the problem is circular. The flame retardant hydrolyzes and releases acid. That acid catalyzes PC chain scission. The retardant meant to protect the part ends up greasing the path to its own failure.
Why notched impact drops before tensile strength
PC toughness comes from a high molecular weight and from chains that entangle and stretch. At a crack tip the material normally goes through shear yielding, chain stretching, and plastic deformation, which soaks up impact energy. As the chains shorten, the material shifts from ductile fracture to brittle fracture.
The practical result is asymmetric. After humidity heat aging the tensile properties often look almost unchanged while the notched impact has already fallen hard. That is why, when you evaluate this compound for dual-85 performance, notched impact retention is a far more sensitive gauge than tensile strength.
Where the damage appears in real parts
The microscopic chain loss becomes very specific reliability failures on the finished part.
| Failure mode | Driving stresses | Early warning sign |
| Screw post cracking | Hoop tensile stress, residual stress, weld line, geometric concentrator | Cracks weeks after assembly |
| Clip brittle fracture | Repeated local deformation at the snap | White marks, then snap on reuse |
| Outdoor brittle fracture | UV, oxygen, heat, water, temperature cycling | Gloss loss, then microcracks |
Screw posts are the classic victim. After the screw is tightened the post carries hoop tensile stress on top of injection residual stress, and it often sits at a weld line or a sharp corner. When new, the material is tough enough to absorb all of it. After aging lowers molecular weight the crack resistance collapses, so a post that was fine at assembly cracks by itself weeks later.
Clips are just as telling. They depend on local plastic deformation every time they snap. Fresh PC/ABS handles the first install, turns white on the second disassembly, and breaks on the third, even while flexural modulus and heat deflection temperature still look acceptable. What actually dropped is the energy needed to start and grow a crack.
Outdoor parts face a worse mix. Beyond humidity and heat they meet UV, oxygen, heat, liquid water, and temperature cycling all at once. Photo degradation, oxidative degradation, and hydrolytic degradation stack, and the part moves from gloss loss and discoloration to microcracks and finally brittle fracture.
How to formulate flame-retardant PC/ABS for humidity heat resistance
The complete hydrolysis resistant design logic runs in one direction.
- Choose a more hydrolysis resistant phosphate ester, because the retardant is the first thing to break down.
- Control or neutralize the acidic species released during aging so they stop catalyzing further damage.
- Protect the PC backbone from continued scission with stabilizers and a dry processing window.
The question to ask is no longer only whether the compound reaches V-0 at molding. It should be how much molecular weight the PC still has after the dual-85 test. Microscopically the loss is molecular weight. To the customer it shows up as screw post cracking, clip brittle fracture, and parts that fail early.
Limitations
This comparison used a single accelerated condition, 107 degrees Celsius under humidity for 90 hours, and two retardants. Absolute molecular weight retention will shift with loading level, PC grade, filler, and the exact humidity heat profile. The directional conclusion holds across aryl phosphates, but qualification should always be run on the actual compound and part geometry.
Bottom line
Flame-retardant PC/ABS that survives humidity and heat is engineered, not assumed. The aryl phosphate flame retardant is often the hidden source of acid that accelerates PC chain scission, so specify hydrolysis resistance and verify molecular weight retention after the dual-85 test rather than trusting a V-0 rating alone.
FAQ
Why does flame-retardant PC/ABS lose impact strength after humidity heat aging?
Flame-retardant PC/ABS loses impact strength because the aryl phosphate flame retardant hydrolyzes under heat and moisture and releases acidic species. Those acids catalyze hydrolysis of the PC carbonate bonds, cutting molecular weight and turning tough parts brittle.
What is the difference between BDP and RDP flame retardant hydrolysis?
BDP and RDP are both aryl phosphate flame retardants but they hydrolyze at different rates. In accelerated testing at 107 degrees Celsius under humidity, RDP dropped PC molecular weight from 55000 to 24000 g/mol in 90 hours while BDP fell from 54000 to 42000 g/mol. RDP is the more aggressive hydrolyzer.
How does a phosphate ester flame retardant accelerate PC degradation?
A phosphate ester flame retardant starts the damage by hydrolyzing its own phosphate ester bonds into acidic P-OH species. In the presence of water and heat those acids catalyze scission of the PC carbonate backbone. The retardant does not sit inertly. It actively speeds up the polymer breakdown.
Why does notched impact drop before tensile strength in aged PC/ABS?
Notched impact depends on molecular weight and chain entanglement far more than tensile strength does. As humidity heat aging cuts PC chain length the material shifts from ductile to brittle fracture. Tensile properties stay nearly unchanged while the energy needed to start and spread a crack collapses first.
What causes screw post cracking in aged PC/ABS parts?
Screw posts carry hoop tensile stress plus injection residual stress and often sit at weld lines or geometric stress concentrators. When new the material is tough enough to absorb those loads. After aging lowers molecular weight the crack resistance drops and the post cracks on its own weeks after assembly.
Why do PC/ABS clips turn brittle after repeated assembly?
Clips rely on local plastic deformation during each snap. Fresh PC/ABS survives the first install, turns white on the second disassembly, and snaps on the third because molecular weight has fallen. Flexural modulus and heat deflection temperature can still look fine while the energy to initiate a crack has already collapsed.
Can flame-retardant PC/ABS survive long term outdoor exposure?
Outdoor use is harsher than the lab because UV, oxygen, heat, water and temperature cycling act together. Photo degradation, oxidative degradation and hydrolytic degradation overlap and drive gloss loss, discoloration, microcracks and finally brittle fracture. Exterior PC/ABS compounds need UV stabilization plus hydrolysis resistance.
What does the dual-85 test measure for PC/ABS?
The dual-85 test exposes a part to 85 degrees Celsius and 85 percent relative humidity for a set duration, commonly 1000 hours. It stresses the two weakest modes for PC/ABS at once. Engineers track notched impact retention and molecular weight because those reveal hidden damage long before tensile strength moves.
How can you improve humidity heat resistance of PC/ABS?
Improve humidity heat resistance by choosing a more hydrolysis resistant phosphate ester, by stabilizing or neutralizing the acidic species released during aging, and by protecting the PC backbone from further scission. Ask for molecular weight retention after 1000 hours dual-85 rather than only a V-0 rating at molded condition.
Is PC hydrolysis alone responsible for the failure?
No. PC hydrolysis alone is too slow to explain the rapid loss seen in aging tests. In flame-retardant PC/ABS the aryl phosphate flame retardant supplies the acid that catalyzes the reaction, so the failure is a synergy between retardant hydrolysis and PC chain scission rather than simple moisture attack on the polymer.
How much molecular weight loss is acceptable after 1000 hours dual-85?
There is no single universal limit but the data show RDP can strip PC down to roughly 44 percent of original molecular weight in 90 hours while BDP leaves about 78 percent. A sensible engineering target is to retain the majority of molecular weight after 1000 hours dual-85 and confirm the result with notched impact retention.
Are aryl phosphate flame retardants unsuitable for every PC application?
No. Aryl phosphate flame retardants remain widely used because they are effective and cost efficient. The risk concentrates in humid hot or outdoor environments and in thin stress concentrated features like screw posts and clips. Dry indoor applications with low stress see far less of the hydrolytic penalty.

