Waste cooking oil softens aged bitumen and restores some low temperature flexibility, while nano iron oxide stiffens the mix and resists rutting. In a reclaimed asphalt study, 9 percent waste cooking oil plus 4 percent nano iron oxide cut rutting depth by 38.60 percent and raised indirect tensile strength by 30.21 percent against a control mix.
Why waste cooking oil is a bio-based modifier rather than a filler
Reclaimed asphalt pavement carries aged binder inside it. That binder has oxidized, lost light fractions, and turned stiffer and more brittle than the bitumen it replaced. Recycle it at a high rate and you face a choice: soften the aged binder, or accept a mix that cracks in cold weather.
The triglyceride-rich residue of frying, known in the trade as WCO, attacks the first side of that choice. Fatty acids and triglycerides in the residue interact with bitumen and shift its chemical composition, which brings viscosity down and returns some of the ductility oxidation took away. That is not a filling action. The material works on the binder phase itself, which is why it behaves differently from a mineral powder that simply occupies volume.
There is a cost attached to the same chemistry. Whatever softens a binder also weakens its resistance to permanent deformation when the pavement runs hot. That trade is the reason a single modifier rarely rescues a reclaimed mix, and the reason this study paired the residue with a stiffening nanoparticle instead of pushing one additive harder.
The mix design and the nine screening runs
Nine mixtures went through an initial screening to bracket each dosage, and five were carried into full testing: a control, a 20 percent reclaimed mix, that mix with nano iron oxide, that mix with the oil, and that mix with both.
| Mix | Composition | Density (g per cubic cm) | Stability (kg) | Flow (mm) | Air voids (percent) |
|---|---|---|---|---|---|
| M0 | Control | 2.33 | 1355 | 3.00 | 4.20 |
| M1 | 20 percent reclaimed asphalt | 2.36 | 1448 | 3.10 | 3.40 |
| M4 | Reclaimed plus 4 percent nano iron oxide | 2.31 | 2372 | 2.60 | 3.43 |
| M7 | Reclaimed plus 9 percent WCO | 2.28 | 2084.5 | 3.75 | 4.03 |
| M8 | Reclaimed plus both additives | Not reported separately | Not reported separately | Not reported separately | Not reported separately |
Even the Marshall columns show the two additives pulling apart. Nano iron oxide lifted stability hard and pushed flow down, which reads as a stiffer mix. The oil also lifted stability against the reclaimed baseline but pushed flow up, which reads as a softer and more workable one. Density dropped in both cases, since the oil is lighter than bitumen and the particles are lighter than the aggregate they replace.
Stability: 1448 to 2372 kg across the additive ladder
Stability is the Marshall measure of resistance to plastic deformation, and the two ladders behave in opposite ways. Against the 20 percent reclaimed mix at 1448 kg, nano iron oxide at 2, 3, and 4 percent lifted stability by 42.88, 48.68, and 63.8 percent. Waste cooking oil at 5, 7, and 9 percent lifted it by 61.94, 52.28, and 43.9 percent.
Keep the shape of those series rather than the individual values. The particle improves monotonically across the range tested, which is what a stiffener should do. The oil peaks at the lowest dosage tried and then falls away, which is what a softener does once the binder has passed its useful consistency. By stability alone, the best oil result sat at 5 percent, not at 9 percent.
That looks like a contradiction, because 9 percent was carried forward as the optimum. The resolution sits in the selection criteria: the choice was made on the whole Marshall set, including flow and air voids against the specification window, not on stability in isolation. Put the ladder and the selection side by side and the logic is clear. The higher dosage buys workability and cold weather behavior, and it pays for them with some stability.
Rutting: the composite mix cut depth to 5.12 mm
Wheel tracking records how far a mix deforms under repeated load at high temperature, and it is the test where a softening additive usually gives ground. Measured depths were 9.83 mm for the control, 8.33 mm for the reclaimed mix, 7.25 mm for the nano iron oxide mix, 9.17 mm for the waste cooking oil mix, and 5.12 mm for the composite.
| Mix | Rutting depth (mm) | Change against the reclaimed mix |
|---|---|---|
| Control | 9.83 | Not applicable |
| 20 percent reclaimed asphalt | 8.33 | 15.30 percent better than control |
| Reclaimed plus 4 percent nano iron oxide | 7.25 | 13 percent lower |
| Reclaimed plus 9 percent WCO | 9.17 | About 10 percent higher |
| Reclaimed plus both additives | 5.12 | 38.60 percent lower |
The oil behaved exactly as its chemistry predicts. It softened the binder, rutting rose about 10 percent against the reclaimed mix, and that combination still finished 6.7 percent better than the control. The particle alone took 13 percent off. Together they took 38.60 percent off, which is far more than the sum of the two separate contributions.
That surplus is the finding worth carrying away. A softener and a stiffener should partially cancel each other. Here they did not, which suggests the pair changes how the binder and the filler network interact rather than simply rebalancing stiffness. The proposed explanation is a stronger cohesion bond linking the particle, the oil, the bitumen, the aggregate, and the reclaimed material at high temperature. It is a reasonable story and an unproven one, because the evidence is mechanical rather than chemical.
Low temperature strength: 2336.5 to 2764.8 kPa
Indirect tensile strength at low temperature reports how much tensile stress a mix carries before it cracks. The numbers were 2123.3 kPa for the control, 2336.5 kPa for the reclaimed mix, 2362.8 kPa for the nano iron oxide mix, 2486.9 kPa for the oil mix, and 2764.8 kPa for the composite.
Notice that the ranking inverts. The oil was the weaker additive under rutting and the stronger single additive under cold tension, which is precisely what a softener should produce. The particle reversed that pattern. The composite led both lists, and that is the argument for pairing two mechanisms instead of raising one dosage.
Gains against the control came to 10 percent for the reclaimed mix, 11.3 percent for the particle mix, 17.12 percent for the oil mix, and 30.21 percent for the composite. Each single number is modest. The combined one is not.
Moisture resistance and interfacial adhesion improved by 8.24 percent
The Marshall immersion test compares stability before and after water conditioning, and the retained stability ratio is what comes out. Against the control, the ratio improved 4.22 percent for the reclaimed mix, 7.33 percent for the particle mix, 5.07 percent for the oil mix, and 8.24 percent for the composite.
Moisture damage is a loss of interfacial adhesion. Water finds the binder and aggregate boundary, interfacial adhesion falls, and the film lifts. The particle is described as working two ways: it absorbs into the bitumen and cuts permeability, and it makes the binder more hydrophobic so water struggles to displace it. The oil is described as laying down a water-repellent barrier through its own oily character while reducing free bitumen and the space between components.
Both descriptions land on the same interface, which explains why the pair leads. A stiffener alone does not necessarily improve adhesion, and a softener alone can make stripping worse. Two mechanisms aimed at the same boundary do better than either one.
The life cycle result is not a clean win
The environmental assessment is where this study needs the most caution, because its outputs do not resolve into one message. The composite raised global warming potential 30.2 percent, eutrophication 52.5 percent, terrestrial ecotoxicity 66.1 percent, and ozone layer depletion 48.8 percent against the control. The 20 percent reclaimed mix, in contrast, delivered the best environmental performance of the modified mixes.
Then the weighting step says something else. The weighted score fell 11.9 percent for the reclaimed mix, 12.39 percent for the particle mix, 11.67 percent for the oil mix, and 9.59 percent for the composite. A lower weighted score means lower overall impact, so that step ranks all four modified mixes as improvements and places the composite ahead of the control.
Both outputs come from the same assessment and they cannot both lead. The category increases are specific and large. The weighted decrease rests on normalization and weighting factors borrowed from an external panel. Treat the category increases as the concrete finding and the weighted score as a scheme-dependent summary. What survives both readings is narrower: reclaimed content is the main environmental lever, and a second additive buys mechanical performance at some environmental cost.
What this means for a bio-based additive program
- Match the additive to the failure mode. The oil helped cold cracking and hurt rutting resistance, and no dosage flips that direction.
- Expect an optimum rather than a straight line. The oil series peaked at 5 percent for stability and was carried at 9 percent for workability, so the target property picks the number.
- Optimize a paired additive as one system. The composite beat both singles on rutting and on tensile strength by more than either contribution explains.
- Run the moisture ratio before and after conditioning. It is the cheapest interfacial screen available, and it moved 8.24 percent here.
- Read life cycle data by category, not only as a weighted score. Global warming potential rose 30.2 percent while the weighted score fell, and both belong in the decision.
- Qualify the incoming oil. The residue varies in free fatty acid content and water, and that variation arrives in the binder.
Limitations
The study reports mechanical performance for a defined aggregate gradation and binder in one location, so the dosages are specific to those materials and should not be transferred as fixed numbers. The mechanism proposed for the composite mix, a stronger cohesion bond at high temperature, is inferred from mechanical results rather than demonstrated by binder chemistry or microscopy of the interface. The environmental assessment uses normalization and weighting factors from an external panel, and its category-level results conflict with its weighted score for the composite mix, so neither can be treated as a standalone conclusion. Rutting and tensile results come from laboratory specimens rather than from a trafficked pavement, and no long-term aging or moisture conditioning beyond the standard immersion step was reported. The oil dosage series shows a peak in stability at 5 percent while the carried-forward optimum was 9 percent, and the paper does not give a full justification for that selection beyond specification compliance.
Bottom line
Waste cooking oil and nano iron oxide handle different failure modes in a reclaimed mix, and the pairing is the point. The oil restored cold temperature ductility and added 17.12 percent to tensile strength on its own. The particle took 13 percent off rutting on its own. Together they delivered 38.60 percent lower rutting and 30.21 percent higher tensile strength than the control, with an 8.24 percent gain in retained stability. The environmental argument is the weaker half, so read the category increases alongside the weighted score rather than instead of it.
FAQ
What does waste cooking oil do to aged bitumen?
Its fatty acids and triglycerides interact with the binder and change its chemical composition, which lowers viscosity and restores some ductility that oxidation had removed. That is a rejuvenating action on the binder phase rather than a filling action. The same softening makes the mix more vulnerable to permanent deformation at high temperature.
Why pair the oil with nano iron oxide?
The two additives move opposite properties. The oil improves low temperature flexibility and workability and costs rutting resistance, while the nanoparticle stiffens the mix and resists deformation. Used together they produced lower rutting and higher tensile strength than either one alone. That is a system effect rather than a simple average of two contributions.
What dosage of the oil worked best?
Stability peaked at 5 percent oil, at 61.94 percent above the reclaimed mix without additive. The study carried 9 percent forward as the optimum because the selection also weighed flow and air voids against the specification window. The right dosage therefore depends on which property is being targeted, and the two answers are not the same number.
How much did rutting depth drop?
The composite mix reached 5.12 mm against 8.33 mm for the reclaimed mix and 9.83 mm for the control, which the study reports as a 38.60 percent reduction against the reclaimed mix. The oil alone raised rutting by about 10 percent against the reclaimed mix, and the nanoparticle alone lowered it by 13 percent.
Why did the composite beat both single additives?
The mechanical results do not settle that question. The proposed explanation is a stronger cohesion bond among the nanoparticle, the oil, the bitumen, the aggregate, and the reclaimed material at high temperature. No binder-level chemical or interfacial evidence is reported, so the synergy is measured but not explained with certainty.
What happened to low temperature strength?
Indirect tensile strength rose from 2123.3 kPa for the control to 2764.8 kPa for the composite, a 30.21 percent gain. The oil mix alone reached 2486.9 kPa, a 17.12 percent gain, and the nanoparticle mix reached 2362.8 kPa. The oil was the stronger single contributor on this measure, which is the reverse of the rutting ranking.
How is moisture resistance measured here?
The Marshall immersion test compares stability before and after water conditioning, and the retained ratio is the result. The composite improved that ratio by 8.24 percent against the control, ahead of the nanoparticle mix at 7.33 percent and the oil mix at 5.07 percent. It is a laboratory indicator of stripping resistance rather than a field performance guarantee.
Does the environmental case support the composite mix?
Not cleanly. The composite increased global warming potential by 30.2 percent, eutrophication by 52.5 percent, terrestrial ecotoxicity by 66.1 percent, and ozone layer depletion by 48.8 percent against the control. The weighted score fell by 9.59 percent, which points the other way. The reclaimed content is the main environmental lever, and the second additive buys performance at a cost.
Why does reclaimed asphalt need a modifier at all?
The aged binder in reclaimed material is stiffer and more brittle than virgin bitumen because oxidation has removed light fractions. Using a high reclaimed content without correction produces a mix that cracks at low temperature. A modifier restores workability or stiffness balance, depending on which direction the mix has drifted.
Can these dosages be used directly in another project?
No. The optimum depends on the aggregate gradation, the binder grade, the reclaimed content, and the local specification window. The values here describe one material set, measured in one laboratory program. A new project should run its own dosage ladder, starting from the direction of the responses rather than from the numbers themselves.
What is the main risk with waste cooking oil as a raw material?
Consistency. The residue varies in free fatty acid content, water content, and degree of oxidation depending on its source and handling. That variation reaches the binder and shifts both viscosity and aging behavior. A specification for the incoming oil is as important as the specification for the dosage.

